Posted by on February 05, 19102 at 07:15:08:

PERSONAL PERTICULAR

NAME :PARIKH NIRAJ KIRITKUMAR

CORRESPONDANCE : C-14 JAI CHAMUNDA SOCIETY,
NEAR ZAVERNAGAR,
WAGHODIA ROAD.
VADODARA-390019(GUJ.)
INDIA.

E-MAIL ADDRESS : parikhniraj@hotmail.com
: Parikhniraj_kiritkumar@yahoo.com

AGE : 29 YEARS (D.O.B. 28-01-1973)

SEX : MALE

MARITAL STATUS : MARRIED

MOTHER TONGUE : GUJARATI

RELIGION : HINDU

NATIONALITY : INDIAN

PASSPORT NO. : A-4036912

EDUCATIONAL QUALIFICATION:

S.S.C.(SCIENCE) 1989 50%

ELECTRONIC FAB. & ASSEMBLY MECHANIC. AHMEDABAD

1991 48%
I.T.I. (MACHINIST) I.T.I. TARSALI VADODARA.

1993 61%

EXPERIENCE:

# Worked with “CADITRONIC PVT. LTD.” Ahmedabad for 6 months from 10-12-1990 to 30-06-1991. Where major work area was soldering of computers P.C.B.

# Worked with “M/S SHREENATH ENGINEERING CO.” Waghodia GIDC estate, Baroda from Aug. 1995 to continue till day. Working as a supervisor /worker/ labor; where my major work was, coordination various activities from purchase to finish products.

 My supervision over six members staff working under me was on work like cutting adjusting according to diameter.

 Also I operate shaping machine, Hand grinder, Pedestal grinder, Surface grinder, Drilling machine (radial drill), Lath machine,Hydrolic Hacksaw machine etc
.
 I have experience of correspondence on type machine with customers along with that wage slip, attendance card salary chart, and basic Computer work of company with INTER-NET.

AREAS OF INTEREST:

Swimming and reading Books.

SHREENATH ENGINEERING WORK EXPERIENCE

Company working mining accessories, & blasting equipment and taking job work have served in the said company & gained and experience of machine operation as well as supervisor & shift incharge. Material C.D.S., M.S., C.I. tubes material as well as grade wise EN-8 to EN-31 in which pipes and hard heavy material is being used.

WORK RESPONSIBILITY :

Grade wise work as per standard of I.S. 10208, 1982/B.S. 4019 part I 1974 & longyear book reading as per standard has also been done in the said company. As a supervisor/machine operator/shift incharge with operation of varnier/micrometer/dial-vernir & gauge.

1 LATH MACHINE :

I have done with the work on lath m/c, of pipe /heavy job turning maintain I.D. & O.D. according to drawing also done taper work ‘v’ thread & square thread, hole, cut-center between-center all operation. This m/c center height is total is 1 mtr. And bad size is 16 feet long & bore center is 135m.m. As a machine operator.

2 DRILL M/C :
I have also worked on drill m/c with responsibility the work of changing drill chuck and drilling operation. Drill size is maximum is 64 m.m.

3 GRINDING M/C :
On this m/c tool grinding, square tool, job finished, job shape, & different type of work carried out as well as bench pedestal grinder operation. Have also worked on surface grinder of precision & job work too of length Thickens Height.

4 SHAPING M/C :
On this m/c big plate, bore, hole with the hole with boring bar is being used in core lifter & key-way of m/c, plats, is also carried out as well as job-work, & radius also done.

5 HYDRAULIC PRESS M/C :
Capacity of this press is 1 tons this m/c also I had worked for pressing as well presses the pipe & Expanded the pipes.

6 WELDING & GAS CUTTING :
The work of miscellaneous work of welding is also done.

7 HYDRAULIC HAXO CUTTING:

The work of cutting of material size wise has also been carried out on this m/c.

FITTER :
The m/c maintenance work, filing, cutting taping, Assembly of S.T.C.B. & D.T.C.B. Are also done. With help of longyear standard. And all kind of fitter works.

SHIFT INCHARGE :

As a shift incharge I have carried on the following work with B.S. standard drill rods, casing, and flush-joint, designing, core –barrel with all type of design & S.T.C.B. & D.T.C.B. all kind of casing coupling and water swivel.
All the dimension of above is in millimeter. Have knowledge of system of dimensional-Identification letters. All decimal dimensions, allowable tolerance, gress spreading are considerable by me. Also see quality control and material inspection by me.
_____________________________________________________________

C.D.S.- Cold Draw Steel, I.S. - Indian Standard
M.S. - Mild Steel. B.S.- British Standard,
C.S.- Casting. M/C- Machine
L.H.- Left Hand R.H.- Right Hand
I.D. - Internal diameter. O.D.- Outer Diameter.